How To Load A Porter Cable Nail Gun

Contents
Table of Contents
Bookmarks

Quick Links

Pin NAILER

Cloueuse de goupilles

Clavadora

Didactics manual

Manuel d'instructions

Transmission de'instrucciones

Française : Page 15

Español: Página 30

www.deltaportercable.com

INSTRUCTIVO DE OPERACIÓN, CENTROS

DE SERVICIO Y PÓLIZA DE GARANTÍA.

LÉASE ESTE INSTRUCTIVO

ANTES DE USAR EL PRODUCTO.

PIN138

1 - ENG

Related Manuals for Porter-Cablevision PIN138

Summary of Contents for Porter-Cable PIN138

Page 1 Cloueuse de goupilles Clavadora Instruction manual Manuel d'instructions Manual de'instrucciones Française : Page 15 Español: Página 30 world wide web.deltaportercable.com INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. PIN138 one - ENG...
Page 2: Definitions - Safety Guidelines
IMPORTANT SAFETY INSTRUCTIONS FOR PNEUMATIC TOOLS Salve THESE INSTRUCTIONS When using whatsoever pneumatic tool, all safe precautions, every bit outlined beneath, should be followed to avoid the hazard of death or serious injury. Read all instructions earlier operating the tool. DEFINITIONS - SAFETY GUIDELINES The definitions below draw the level of severity for each bespeak word.
Page 3 • Do non use bottled gases to power this tool. Bottled Fig. E compressed gases such as oxygen, carbon dioxide, nitrogen, hydrogen, propane, acetylene or air are not for use with pneumatic tools. Never apply combustible gases or whatever other reactive gas as a ability source for this tool.
Page 4 • Do non overreach. Maintain proper basis and balance Fig. K at all times. Loss of balance may cause personal injury. (Fig. K) • Make sure hose is free of obstructions or snags. Entangled or snarled hoses can cause loss of residual or footing.
Page five • Grip tool firmly to maintain control while allowing tool Fig. P to recoil abroad from work surface every bit fastener is driven. • Practise not actuate the tool unless the tool is placed firmly confronting the workpiece. (Fig. T) • DEPTH ADJUSTMENT: To reduce hazard of serious injury from accidental actuation when attempting to accommodate depth, ALWAYS: •...
Page vi: Tool Parts
Nails 23 gauge wire (headless or slight head pins) Lengths 5/8" (16 mm) –1-3/8" (35 mm) Air Inlet 1/4" NPT (half-dozen.iv mm) NOTE: Use only PORTER-CABLE canonical fasteners TOOL PARTS Fig. i Trigger B. Safety trigger C. Air Inlet with quick connect coupler D.
Folio 7: Operation
AIR Plumbing equipment The tool is equipped with a 1/4" (six.4 mm) male person quick connector coupling. A 3/8" (9.five mm) male quick connector coupling is bachelor from PORTER-CABLE and may be used when a 1/4" (half-dozen.4 mm) supply line is not available. NOTE: A 3/8" (9.5 mm) supply line (and fittings) are required for maximum tool functioning.
Page viii: Actuating Tool
The trigger is locked off until the safety trigger is depressed. LOADING THE TOOL (FIG. 1–3) Go on the tool pointed abroad from yourself and others. Serious personal injury may result. Never load nails with the trigger activated. Personal injury may result. Read all Safety Warnings before using tool.
Page 9: Adjusting Depth
ADJUSTING DEPTH The depth that a fastener is driven is controlled past the pressure level of the air supply. The corporeality of air pressure required volition vary depending on the length of the fastener and the material beingness fastened. Experiment with the air pressure setting to decide the lowest setting that volition consistently perform the job at hand.
Page 10: Cold Weather Operation
Annotation: Should nails continue to jam frequently in nosepiece, accept tool serviced by an authorized PORTER-CABLE service center. Cold Weather condition Functioning When operating tools at temperatures below freezing: Make certain compressor tanks accept been properly drained prior to use. Keep tool as warm every bit possible prior to use.
Page eleven: Maintenance
We cannot guarantee repairs made or attempted past others. You can besides write to us for data at PORTER-CABLE, 4825 Highway 45 North, Jackson, Tennessee 38305 - Attending: Product Service. Be sure to include all of the information shown on the nameplate of your tool (model number, type, series number, etc.).
Page 12: Three-Twelvemonth Limited Warranty
xc 24-hour interval Coin Dorsum GUARANTEE: If yous are not completely satisfied with the functioning of your PORTER-CABLE Power Tool, Light amplification by stimulated emission of radiation, or Nailer for any reason, yous tin can render information technology within 90 days from the engagement of purchase with a receipt for a total refund – no questions asked.
Page 13: Troubleshooting Guide
Only a few fasteners are Reload fasteners to left in the magazine brainstorm firing again. Other Contact a PORTER- Cablevision Authorized Warranty Service Center TOOL SPECIFICATIONS PIN138 Height (inch/meter) 7.v/.xix Width (inch/meter) 1.9/.05 Length (inch/meter) 8.1/.21 Weight (lbs/kg) 2.1/0.95 Recommended Operating Pressure 60-100 psi (iv.i to half-dozen.nine bar) Air Consumption per 100 cycles 1.61 SCF...
Page 14 Compressor will be sufficient for tools at all product rates. Compressor will be sufficient at slow or moderate production rates, but may have difficulty at very rapid rates. Compressor volition exist adequate only when tools are utilized at tedious production rates (dial-out or occasional utilize). Non Recommended Portable 5.five HP Gas...